Industry & infrastructure

Inspection software for machines, installations and infrastructure

Findings directly on the asset, with photo, location and status. Reports ready for your compliance dossier.

Technician with a tablet at a pump installation, with the asset on the screen of the app

Machines, installations, buildings - industrial assets need regular checks to meet safety standards and prevent costly downtime. But when findings are scattered across paper forms and email threads, follow-up becomes a gamble.

PinPoint lets technicians mark findings directly on a visual representation of the asset. Every defect gets a photo, a location and a status - visible to everyone who needs to act on it. Reports are generated automatically, ready for your compliance dossier.

Why now?

Preventive maintenance reduces unplanned downtime by up to 40%. But only if findings are consistently documented and followed up. That is exactly what PinPoint does.

How an inspection round of machines runs

Whether it is a production line, a pumping station or a building, the round always follows the same four steps.

1

Pick the round

A round is a bucket: the monthly check of hall 2, the annual round of the lifting equipment. It holds the assets that are due.

2

Open the asset

A photo, a plan or a 3D model of the machine. The inspector immediately sees what was found in earlier rounds.

3

Pin the finding

At the spot where the problem is, with your own questionnaire, the severity and photos. Also without a network, in a basement or plant room.

4

Follow up to closure

An owner, a deadline and a status. The item stays open until someone has checked the repair.

What it is used for

For many installations the law requires periodic inspections, and the inspectorate wants to see what happened to the remarks. The inspection itself is done by an approved body; what you do before and after, you record in PinPoint.

The rules that come up most

In Belgium, checked in September 2026:

Work equipment
The Belgian Code on well-being at work (book IV, title 2) requires the employer to maintain work equipment and have it inspected periodically, and to record the results in writing and keep them available for the inspectorate.
Lifting equipment
A thorough examination by an external technical inspection service (EDTC) at least every twelve months, and safety parts such as cables, chains, hooks and brakes at least every three months (ARAB art. 280 and 281, Code book IV, title 4).
Electrical installations
Under the AREI (book 1), a non-household low-voltage installation gets a periodic visit from an approved body every five years, a high-voltage installation every year. Defects that are found must be remedied without delay.
ISO 55001:2024
The standard for an asset management system: how an organisation manages its assets and decides about them over their whole life.

Inspection report in? Put the remarks in PinPoint

Every remark from a report by an EDTC or approved body becomes a finding on the asset, with an owner and a deadline. At the next inspection you show per remark what was done, instead of a folder of reports.

PinPoint is inspection software, not an inspection body. Whether an installation complies is decided by the approved body and by how you work.

From loose items to insight

Logging a finding is the start, not the goal. Because every finding is attached to the asset and structured, you see the history per machine, which problems keep coming back and where to steer, and you can respond with an owner, a priority and a deadline. A shipping company uses that history as the basis for predictive maintenance. See how that works on board.

What is an asset inspection?

An asset inspection is a periodic check of a machine, installation or part of a building for wear, defects and deviations from the safety standard. Together the findings form the history of that asset: what was found when, by whom, and what happened to it. That history is what an auditor wants to see.

Frequently asked questions

What is the difference between an inspection and preventive maintenance?

An inspection establishes what the condition is. Preventive maintenance is the work that follows from it, or that is scheduled at fixed intervals. The inspection provides the trigger and the evidence; without structured findings, preventive maintenance becomes guesswork. PinPoint handles the inspection side and can pass its findings on to your maintenance system.

Can I find the inspection history per machine?

Yes. Every finding is attached to the asset, not to a loose form. Per machine you see what was found in earlier rounds, what has been resolved and what is still open. The next inspector therefore starts from what is already known, and the history per asset stays complete, with photos and status changes.

Can I export inspection data to our own systems?

Yes. Reports can be exported as PDF, and the underlying data can go to Excel, CSV, Power BI or your own systems, also through an API. PinPoint is set up as a data product: your inspection data stays yours, and there is no lock-in if you ever want to move it elsewhere.

Other use cases

All use cases

Not sure if PinPoint fits your process?

We will be honest with you. If PinPoint is not the right fit, we will tell you. No hard sell, no obligations. Just a conversation between people who understand inspections.

Last updated on